Registered Address: 32D Floor Guomao Building, No.388, Hubin South Road, Siming District, Xiamen,Fujian, China

DI890 3BSC690073R1 is an ABB s800 8-channel intrinsic-safety digital input module used with the documented Advant S800 I/O platform. Selection must match the complete product identity, hardware execution, connected assemblies and approved system configuration.
Before replacing DI890 3BSC690073R1, compare the supplied nameplate, revision, connectors or terminals and installed position with the original equipment record. After installation, review diagnostics and complete the approved functional checks before service.
DI890 3BSC690073R1 is an ABB s800 8-channel intrinsic-safety digital input module selected by its complete product identity and documented equipment role. Its suitability depends on the installed Advant S800 I/O system, hardware execution, interfaces and application requirements matching the supplied unit. Visual similarity or a shortened code is not proof of interchangeability.
Before replacing DI890 3BSC690073R1, record the full nameplate, installed position, connector or terminal arrangement, paired equipment and relevant ABB service information. After installation, verify power, communication and control interfaces, complete the approved functional checks and confirm stable operation before returning the equipment to service.
ABB DI890 3BSC690073R1 documentation and reference links.
Important Notice: Every linked document must identify the listed model or its documented family. Confirm the complete order code, hardware revision and installed-system requirements before replacement.
Each of the eight channels is an intrinsically safe digital input. ABB specifies NAMUR proximity sensors or voltage-free contacts as signal sources. For NAMUR sensors, the module supports line-fault detection without external components. When voltage-free contacts are used, ABB states that external series and parallel resistors are required if line faults are to be detected. Do not apply a general-purpose 24 V discrete-input wiring assumption to this module.
ABB specifies built-in current-limited sensor power, short-circuit protection to ground and 30 V, and over-voltage and over-temperature protection. Intrinsic safety depends on the approved transmitter, MTU, wiring and hazardous-area entity design; verify certification, zone and control drawing before connection.
ABB specifies individual galvanic isolation between channels, from circuit common ground, the supply and ModuleBus. Rated insulation voltage is 50 V and dielectric test voltage is 500 V AC. Selectable digital filter times are 2, 4, 8 or 16 ms; ABB also lists a 1 ms analog filter. The input stage is powered from the 24 V supply connections through the module's internal conversion.
Front indications include fault, run, warning and channel 1–8 status/fault; internal process-supply and loop supervision are documented. ABB lists 1.4 W power dissipation, typical 120 mA (maximum below 150 mA) from +5 V ModuleBus and typical 50 mA (maximum below 70 mA) from the +24 V external supply. Confirm module diagnostics, filter settings and MTU connections in the actual controller configuration.
ABB specifies S800 mechanics and compatibility with TU890 or TU891 compact MTUs. TU890 is listed for Ex applications and TU891 for non-Ex applications. The manufacturer lists 45 × 102 × 119 mm (W × D × H), or 111 mm depth including the connector, and approximate bare-module weight of 0.20 kg; neither figure is packed shipping data.
ABB lists operating ambient 0 to +55 °C, storage −40 to +70 °C, 5–95% RH non-condensing and IP20. For vertical mounting in a compact MTU, the published maximum ambient is 40 °C. Verify orientation, enclosure, pollution/corrosion conditions, certification and the S800 installation manual for the installed revision.
DI890 provides eight NAMUR or voltage-free-contact inputs. Each channel includes intrinsic-safety interface components, current-limited sensor power and short-circuit protection to ground and 30 V. ABB documents over-voltage and over-temperature protection. Use only the sensor, MTU, field wiring and entity parameters accepted by the approved hazardous-area design.
For NAMUR sensors, the manufacturer describes line-fault detection without additional external components. For voltage-free contacts, add external series and parallel resistors when line-fault detection is required, following ABB's wiring instructions.
ABB specifies TU890 for Ex applications and TU891 for non-Ex applications, with S800 ModuleBus integration. Individual galvanic isolation is provided channel-to-channel and from the supply, ground and ModuleBus. Selectable digital filtering is 2, 4, 8 or 16 ms, with a 1 ms analog filter.
Documented diagnostics include fault, run, warning and channel 1–8 status/fault LEDs, plus internal process-supply and loop supervision. ABB lists 1.4 W dissipation, +5 V ModuleBus current typically 120 mA (maximum below 150 mA), and +24 V external current typically 50 mA (maximum below 70 mA). Confirm channel modes, filter, diagnostics and MTU wiring in the approved station configuration.